The Martin MAC Viper line of automated luminaires are extremely popular due to their extensive feature set, great color mixing, small size and weight, quiet operation and more. DMX 512-Interface compatible with PC, Mac & Linux XLR 5 pol Output (non-isolated) compatible with. USB 2.0 input and single DMX512 output (non-isolated), RDM is not supported on this device. With the Open DMX-USB Interface ENTTEC offers a cost-effective Interface which enables the DMX-512 Standard with PC, Mac or Linux.Taking on some iconic design elements from the classic Martin 1220 and Martin 518 scanners, the RUSH Scanner 1 LED is a totally new and updated fixture.The RUSH Scanner 1 LED is based on a 90W white LED engine the unit boasts an impressive 2300 Lumen output from the fixed 15 degree lens. The Philips MSR Gold 1000 MiniFastFit lamp has a slightly longer lifetime (900 hrs.) than the Osram lamp, but a little lower output (-10%) and a CRI around 80.The lamp can be ordered as Philips code 928171405115 or Martin P/N: 97010350.The following comparison chart utilizes data supplied by the lamp manufacturers and is a great way to understand the differences between the lamps:Martin Professional has released a new mirrored fixture called the RUSH Scanner 1 LED. The only downside being a slightly lower output (-5%) compared to the standard lamp.The lamp can be ordered as Osram code 53973 or Martin P/N: 97010351.Martin has also approved an alternate lamp from Philips for the MAC Viper series. The output appears more brilliant and the colors from the CMY mixing system even more vibrant than with the standard lamp.
One of the little-known functions is that M-PC enables one universe of output for FREE. Weighing in at only 21 lbs (9.6kg), the RUSH Scanner 1 LED is a great choice for many installations and productions.The yoke is adjustable and can both extend and be used as a floor stand!The following video shows the RUSH Scanner 1 LED in action:Martin M-Series systems have many great features that allow programmers to create exciting and dynamic lighting cues and shows. Movement is accomplished by moving the mirror through its 170 degree pan and 75 degree tilt. Usb Dmx Controller For Martin Drivers Are InstalledNote that before you can use your ENTTEC device you will need to ensure its drivers are installed. With these units you can simply plug in the DMX line to the USB device and start programming. The only M-Series functions that are disabled are DMX IN and RDM capabilities.In addition, with M-PC you can also access the FREE universe of DMX control via any ENTTEC capable USB to DMX device (USB DMX PRO, PRO MKII and OPEN USB DMX). There are no time restrictions or DMX interruptions, so anyone could use this in a show environment. You simply have to connect the Ethernet from your computer to a node or Art-Net/sACN capable device. For instance, if the aura effect is in red and you have a magenta scroll in place then the audience will still see a red aura. By using the properties of wavelength transmission you can create some interesting effects. This means you can achieve colored strobes in addition to just white output.Furthermore, when combined with the Aura effect, many unique looks become possible. Of the many features, one of the coolest is that the unit works with the original Atomic Colors. Simply plug the 4-pin XLR between the Atomic 3000 LED and the Atomic Colors.Next, set the following menu items on the Atomic Color unit: This provides power and communication to the scroller and ensures that the Atomic 3000 LED is aware that the scroller is connected. First, be sure to always use the internal power supply in the Atomic 3000 LED. This works with other colors and other combinations as well.When using the Atomic Colors on the Atomic 3000 LED there are a few things you must be sure to configure on the Atomic Color unit. This can prove to be very interesting as a red light appears to output magenta. For example, if the number is 3 then every third fixture will be selected. The Mode options are as follows:Every - Selects every "xth" fixture, where "x" is the number in the counter. Using the Next/Last button will cycle through the various mode subsets. First you select the type, then adjust the Mask Value as desired. Have fun strobing in color and creating awesome effects by combining the aura and the scroller colors.The Mode section of the window is where you can select a mask to apply to the current selection. You should also always check in the Atomic 3000 LED menu that is confirms that the scroller is connected: INFO → COLOR SCROLLER → CONNECTEDNow your Atomic 3000 LED with Atomic Colors is ready to go! Programming is very straight forward as long as you have the correct libraries and DMX address in your console. For instance, if the counter is set to 4 then the first 2 fixtures and the last 2 fixtures in the selection will be selected. For example, when you select 12 fixtures then set the counter number to 3 then there will be three blocks of four fixtures.Mirror - Selects "x" number of fixtures, half from the top of the selection and half from the bottom of the selection. For example if the number is 3, then the first 3 fixtures will be selected, then the next 3 and so on.Divide - Splits the fixtures into "x" equal blocks. However there are many downsides to using DMX to control pixels and display video. All the products including VDO Sceptron, Exterior Pixline, and VC grids, strips, and dots can be controlled by either DMX or via the Martin P3 system controller.With DMX you simply address each product via RDM and then use a lighting controller or media server to map the control of the pixels. For example, if you choose groups 1, 2, 3, and 4 then use the Next/Last keys, it will cycle through the groups instead of the individual fixtures.Martin Professional makes some great creative video products that can add excitement and imagery to any production or architectural installations. This allows for easy identification and setup as well as thermal reporting and throttling. (See this previous post about P3-PC)The P3 system controllers also have the ability to receive 2-way communication from each connected device. Plus for no cost, you can use P3-PC to prepare your video mappings and use test program for setups. With a range of products available including the P3-100, P3-200, P3-300, and P3-PC the system is totally scale-able depending on the number of pixels you wish to control. Although many productions can be successful when controlled by DMX, most users prefer the P3 control system for the best video playback on any of Martin's video products.The P3 system controller allows not just easy setup and configuration of a video system, but it also processes video input exceptionally well. This dimming curve best emulates a typical incandescent lamp's dimming abilities. Although mathematically uniform, this dimmer curve is often not the most desired by lighting designers.S-Curve - provides a finer control at lower and higher levels while being more coarse at medium levels. This functionality allows direct P3 control and processing to be output from the media server itself.To fully understand the difference between using DMX and a P3 system controller check out this video that details the differences:Linear - provides an even distribution of light in correlation to the DMX level of the dimmer channel(s). In addition, users can now install P3 onto Hippotizer V4 media servers from GreenHippo. Color temperature adjustments, on-the-fly mapping changes, as well as gamma adjustments are just some of the robust features. Blackberry passport software for macUseful for low level scenes and chases as more DMX values are allocated for dimming at the bottom end.
0 Comments
Leave a Reply. |
AuthorStephen ArchivesCategories |